Contrast Equipment Logo

Call Toll Free: 800-280-2412

1449 N Topping, Kansas City, Missouri 64120
Home Contact Us Search Order Online
 

Trigger Happy

 

How does your spray gun shape up?

No matter how experienced the sprayer, merely triggering and moving a gun in space will not reveal any of the performance characteristics vital to a top quality finish. A simple brief static spray pattern will immediately highlight any potential problems before the gun is used on the painstakingly prepared workpiece or vehicle.
 

Follow the procedure explained below and compare the pattern to our examples. If your result resembles examples 2-8, then look at the corrective measures before you apply paint to the workpiece.

 

1. Ensure that you have the correct air cap, fluid tip and needle set-up on the gun to match the material being applied.

2. Tape up a piece of brown paper - approx. 20” (1/2m) square - onto the spray booth wall at shoulder height.

3. Having set the gun at the recommended inlet or atomizing air pressure, hold it at the correct target distance and spray at the paper WITHOUT MOVING THE GUN.

 

Normal Pattern - Ready to Spray

• Good balance and uniformity
• Symmetrical pattern shape
• Good working height and width
• Uniform distribution of material
(Verify by horizontal spray out)

 

Intermittent Spray Fan or Fluttering

Air in the fluid passageways
• Insufficient paint in cup
• Fluid tip loose
• Fluid needle packing or packing screw loose
• Cup vent hole clogged

 

Banana Pattern

• Air cap horn hole dirty or damaged
• Clean air cap thoroughly
• Replace air cap if necessary

• Test spray pattern, rotate 180° and test again to isolate horn hole location

 

Heavy Top or Bottom Pattern

• Fluid tip or air cap dirty or damaged
• Test spray pattern, rotate 180° and test again to isolate case
• Clean both items thoroughly
• Replace fluid tip or air cap if necessary

 

Single Split Pattern

• Too much air for fluid quantity used
• Reduce air pressure at regulator
• Increase fluid flow by changing fluid tip size or opening needle control knob

 

Center Heavy Ellipse

• Bad air or paint setting
• Viscosity too high, thin with solvents
• Fluid flow too high – reduce
• Air pressure too low – increase

 

Double Split Pattern

• Too much air for fluid quantity used
• Reduce air pressure at regulator
• Increase fluid flow by changing fluid tip size or opening needle control knob

 

Ball End Heavy Pattern

• Too much air flow
• Change fluid tip for smaller size
• Reduce flow using fluid needle control
• Reduce fan size using fan control

 

STATIC PATTERN TEST - PATTERN RUN OUT

Having examined the vertical spray pattern for uniformity of shape and size, now turn the air cap through 90° and static spray a horizontal pattern making sure you trigger for long enough to load the shape with material. Then watch to see the formation of the run-outs of material across the full width of the sprayed pattern. This will highlight how well the material is distributed throughout the spray pattern. If run-out is more obvious at the center or at the ends then this indicates a problem.

Typical Good

Typical Bad

*Note: The information on this website was provided by DeVilbiss

 

Contact Us

Have questions about a product or
solution? Fill out a Contact Form
or email or call us.

Email: Contrast@Contrastequipment.com
Call: 800-280-2412
Hours: Mon-Fri, 8 am – 4:30 pm

 

Quick Links

» Spray Guns

» Powder Spray Finishing

» Wood Spray Finishing

» Pumps

» Sealant, Adhesive & Hotmelt

» Sanitary Pumping & Metering

» Fiberglass & Gelcoating

» Complete Systems

 

Contrast Equipment
1449 North Topping
Kansas City, MO, 64120
Toll Free: 800-280-2412
Local Phone: 816-241-2412
Email: Contrast@Contrastequipment.com

 

Contrast is a division of

© 2015 Contrast Equipment, Inc. All Rights Reserved.